Analog Programming

FuG Elektronik GmbH, Florianstraße 2, 83024 Rosenheim, GERMANY

Analog Programming

All FuG power supplies are optionally available with an analog programming 0-10V (Standard with the series HCE and HCN 7E). This option is also available as retrofit set.

Functions:
Set values for voltage and current
Monitor outputs for voltage and current
Output ON/OFF

Printer friendly data sheet (PDF)

Connector SubD 15pol.

Design example (click to enlarge):

1)	Status report "current control"
2)	Status report "voltage control"
3)	Monitor output "Current" 0-10V
4)	Slider front panel potentiometer voltage adjustment
5)	Slider front panel potentiometer current adjustment
6)	0V, reference for digital signals
7)	n.c.
8)	Input set value voltage 0-10V
9)	0V, reference for analog signals
10)	+10V reference voltage
11)	Monitor output "Voltage" 0-10V
12)	Output ON/OFF (Connection to pin 6) (not for HCK)
13)	n.c.
14)	n.c.
15)	Input set value vcurrent 0-10V

1) 2) 4) 5) 15) at HCN 7E series not connected

Usually the "0V" of the programming voltage (pins 6 and 9) is connected to one of the outputs of the unit. If this is not wanted, the unit may be equipped with an floating analog programming (Pins 4 and 5 not connected in this case).
The following versions are possible:
Isolation max. 600 V DC with respect to the unit output, 30 V DC with respect to ground,
Isolation max. 2 kV DC with respect to the unit output, 30 V DC with respect to ground.
On request we deliver a fiber optical isolation up to 200 kV.
For the most models the floating analog programming can be installed later at our site. On request please ask us! Please indicate in that case the serial number of the appropriate unit.

Important Note:
For turning on the output of your power supply the connection of both of pins 8) and 15) is required. Furthermore on pin 12) must be given the ON-command (connection to "0V").

to top of the page

zur deutschen Version

05.02.09 15:16

Impressum - Legal Notice:

Diese Seite wird betrieben von der FuG Elektronik GmbH, Florianstraße 2, 83024 Rosenheim.
Geschäftsführer: Dr. Hartmut Simon (Vorsitz), Anton Elsasser, Gerhard Huber.
Telefon +49 8031 2851 0
Telefax +49 8031 81099
Registergericht: Traunstein HRB 8638, Umsatzsteuer-Ident-Nr: DE 16 18 91 071.

This page is managed by the FuG Elektronik GmbH, Florianstrasse 2, 83024 Rosenheim (Germany).
Board of Directors: Dr. Hartmut Simon (CEO), Anton Elsasser, Gerhard Huber.
Telephone +49 8031 2851 0
Telefax +49 8031 81099
Commercial court: Traunstein HRB 8638, VAT NR: DE 16 18 91 071.

Mit Anregungen und Hinweisen zu diesen Seiten wenden Sie sich bitte an :
With your suggestions or comments concerning this pages please contact:
webmaster@fug-elektronik.de

Trotz sorgfältiger inhaltlicher Kontrolle übernehmen wir keine Haftung für die Inhalte externer Links. Für den Inhalt der verlinkten Seiten sind ausschließlich deren Betreiber verantwortlich. (siehe auch HAFTUNGSAUSSCHLUß)
In spite of thorough check of the contents we do not take over any liability for the contents of external links. For contents of linked websites are responsible exclusively the persons who running them. (see NON LIABILITY STATEMENT- disclaimer)