FuG Elektronik GmbH, Florianstraße 2, 83024 Rosenheim, GERMANY

Home ▲ Options Accessories Cable Mounting Controls Name Plate Terms & Definitions


At this page we would like briefly to make you familiar with the substantial control elements at the front panels of typical FuG - power suplies.  In order to get an explanation, move the mouse- pointer across the control elements of the front panel.  (Works with Internet Explorer.)

Example HCP   Example HCL    Example HCN    Example cabinet

The picture shows the front panel design of one of our high-voltage power supplies of the HCP- series. In principle this design corresponds also to our medium- voltage power supplies MCP. Since the latter ones are equipped with floating output, the polarity- switch there  is not available.
In principle this design corresponds as well  to table- top- units of other series (built from 2006). Dependent on the output voltage, the output- connectors may be of different design.
In order to get an explanation, move the mouse- pointer across the control elements of the front panel.  (Works with Internet Explorer.)

Mains switch Ten-turn-potentiometer for adjusting of voltage Ten-turn-potentiometer for adjusting of current Polarity-switch for changing of output polarity (optional with HCP) Button to change mode of control from local to external Digital meter for output voltage 4 ½ digit Digital meter for output current 4 ½ digit Light emitting diode ''Warning Overtemperature'' Light emitting diode ''Operating mode power limit'' Light emitting diode ''Operating mode voltage regulation'' Light emitting diode ''Operating mode current regulation'' Light emitting diode ''Output polarity positive'' Light emitting diode ''Output polarity negative'' Light emitting diode for supervision of digital interface (optional) Button to change external mode of control from analogue to digital Light emitting diode ''Local control'' Light emitting diode ''Control digital'' Light emitting diode ''Control ananlogue'' Light emitting diode ''Power output released'' Button to release (ON) or lock (OFF) the output Potentiometer to set the overvoltage protection Button to display the set-values Ten-turn-potentiometer for fine adjusting of voltage (optional) Ten-turn-potentiometer for fine adjusting of current(optional) Light emitting diode ''Overvoltage limitation''

to top of the page

The picture shows the front panel design of one of our high-voltage power supplies of the HCL- series. In principle this design corresponds also to our medium- voltage power supplies MCL. Since the latter ones are equipped with floating output, the polarity- switch there  is not available.
In order to get an explanation, move the mouse- pointer across the control elements of the front panel.  (Works with Internet Explorer.)

Mains switch Ten-turn-potentiometer for adjusting of voltage Ten-turn-potentiometer for adjusting of current Polarity-switch for changing of output polarity (optional with HCL) Switch for changing mode of operation from front panel or from external digital or analog interface (optional) Digital meter for output voltage five digits, if the first digit is max. a ''2'', else four digits Digital meter for output current five digits, if the first digit is max. a ''2'', else four digits Light emitting diode ''Warning Overtemperature'' Light emitting diode ''Operating mode power limit'' Light emitting diode ''Operating mode voltage regulation'' Light emitting diode ''Operating mode current regulation'' Light emitting diode ''Output polarity positive'' Light emitting diode ''Output polarity negative'' Light emitting diode for supervision of digital interface (optional)

to top of the page

The picture shows the front panel design of one of our high-voltage power supplies of the HCN- series. In principle this design corresponds as well  to table- top- units of other series (built till 2005). Dependent on the output voltage, the output- connectors may be of different design. The polarity- switch is available optionally only for high voltage units. Table- top- units of full 19''- width are equipped with two digital instruments - each for voltage and current, instead of the one with the changing- switch. 
In order to get an explanation, move the mouse- pointer across the control elements of the front panel.  (Works with Internet Explorer.)

Digital meter for output voltage and current (3 1/2 digits, changeable between voltage and current) (If required 4 1/2 digits available.) Changeover switch ''voltage/current'' for meter. This switch doesn't exist in units with two separate meters. (from 700W up) Mechanical polarity-switch (optional) CAUTION: To be operated only with output voltage=''0'' Ten-turn-potentiometer for adjusting of voltage If required additional ten-turn-potentiometers for coarse/fine- adjustment can be equipped (possibly with bigger case) Ten-turn-potentiometer for adjusting of current If required additional ten-turn-potentiometers for coarse/fine- adjustment can be equipped (possibly with bigger case) Light emitting diode ''Operating mode current regulation'' Light emitting diode ''Operating mode voltage regulation'' Switch for changing mode of operation from front panel or from external digital or analog interface (optional) Mains switch Grounding connector - galvanically connected with the earthing wire of the mains and with the case. At the rear side another grounding pin with exceptionally low resistance is located. Earhty output connector ''0V''. The galvanical connection of this connector with earth may be removed if necessary. In this case the earthy output may be operated floating up to 300V against the case. High voltage output connector

to top of the page

The picture shows the front panel design of one of our cabinet- designed high-power units with three- phase mains connection. The shown design in priciple corresponds to cabinet- units of all series.  Especially with power- supplies of high output power the design may vary depending on the kind of application and on customers demands, due to additional or different control elements.
In order to get an explanation, move the mouse- pointer across the control elements of the front panel.  (Works with Internet Explorer.)

Hour counter (variant) Light emitting diode for fault- supervision ''Interlock intern'' Light emitting diode for fault- supervision ''Interlock extern'' Light emitting diode for fault- supervision ''internal fault'' Light emitting diode ''OK'' for supervision of internal operational voltage supply Measuring connectors for internal operational voltage supply Internal fuse for interlock- module Internal fuse for pre- stabilization module Button with indicator light ''unit ON'' Button with indicator light ''unit OFF'' Button ''RESET'' for resetting the interlock state Measuring connectors for voltage- and current- monitor Digital meter for output voltage (3 1/2 digits) (If required 4 1/2 digits available.) Digital meter for output current (3 1/2 digits) (If required 4 1/2 digits available.) Ten-turn-potentiometer for adjusting of voltage If required additional ten-turn-potentiometers for coarse/fine- adjustment can be equipped. Ten-turn-potentiometer for adjusting of current If required additional ten-turn-potentiometers for coarse/fine- adjustment can be equipped. Light emitting diode ''Operating mode voltage regulation'' Light emitting diode ''Operating mode current regulation'' Switch for changing mode of operation from front panel or from external digital or analog interface (optional) Light emitting diode for supervision of digital interface (optional) Mains switch/ automatic circuit breaker Automatic circuit breaker for electronics part Indication lamps for supervision of mains phases Hour counter Indication lamps for supervision of mains phases (variant) Mains switch (variant)

to top of the page

zur deutschen Version

 22.10.12 08:27

Impressum - Legal Notice: 

Diese Seite wird betrieben von der FuG Elektronik GmbH, Am Eschengrund 11, 83135 Schechen.
Geschäftsführer: Dr. Hartmut Simon (Vorsitz), Anton Elsasser.
Telefon +49 8039 40077 0
Telefax +49 8039 40077 99
Registergericht: Traunstein HRB 8638, Umsatzsteuer-Ident-Nr: DE 16 18 91 071.

This page is managed by the FuG Elektronik GmbH, Am Eschengrund 11, 83135 Schechen (Germany).
Board of Directors: Dr. Hartmut Simon (CEO), Anton Elsasser.
Telephone +49 8039 40077 0
Telefax +49 8039 40077 99
Commercial court: Traunstein HRB 8638, VAT NR: DE 16 18 91 071.

Mit Anregungen und Hinweisen zu diesen Seiten wenden Sie sich bitte an :
With your suggestions or comments concerning this pages please contact:
webmaster@fug-elektronik.de 

Trotz sorgfältiger inhaltlicher Kontrolle übernehmen wir keine Haftung für die Inhalte externer Links. Für den Inhalt der verlinkten Seiten sind ausschließlich deren Betreiber verantwortlich. (siehe auch HAFTUNGSAUSSCHLUß)
In spite of thorough check of the contents we do not take over any liability for the contents of external links. For contents of linked websites are responsible  exclusively the persons who running them. (see NON LIABILITY STATEMENT- disclaimer)

Stand: 18. September 2012
© FuG Elektronik GmbH